FAQ: Water Based Direct Metal Xo Paint What Sprayer Tip Size?

How do you know what size spray tip to use?

Choose a tip with an orifice size rated for the paint or coating you’ll be spraying. Light coatings such as lacquers, stains, and enamels require a small tip, while heavier coatings such as texture require larger spray tips.

What is a 515 spray tip used for?

Achieve greater control and less overspray on different surfaces with a wide range of coatings, from stains to exterior paints. 10 inch spray pattern ideal for larger surfaces such as houses/buildings, walls and ceilings.

What size tip do I need to spray metallic paint?

For spraying a whole car, a 1.3mm tip is recommended. The 1.4mm tip is perfect for base coats and metallic as the droplet size allows the particles to self-orient to eliminate streaking and mottling.

What is the best size nozzle for spray painting?

A general rule of thumb is: Heavy-bodied primers and primer surfacers work best when you use a nozzle size of 1.7 to 2.2. Basecoats should be sprayed with a 1.4 to 1.6 nozzle. Clearcoats should be sprayed with a 1.3 to 1.7 nozzle.

You might be interested:  FAQ: How To Buy A Paint Sprayer?

What size tip should I use to spray cabinets?

Spray Tip Selection When spraying water-based enamel and satin finish paint, it’s best to use a 311 spray tip as it will deliver a 6-inch spray fan that is perfect for cabinets and smaller doors.

What is a 517 spray tip used for?

Achieve greater control and less overspray on different surfaces with a wide range of coatings, from stains to exterior paints. 10 inch spray pattern ideal for larger surfaces such as houses/buildings, walls and ceilings.

How do I get a smooth finish with an airless sprayer?

Just wait till the paint is dry and lightly sand it with a fine grit sanding block to smooth it over. Paint over it again and you should be good to go! Here’s a quick video to demonstrate how I spray paint and get a flawless finish every time.

What is a 211 spray tip used for?

The 211 spray tip is used to work with light lacquers and spray more accurately. For example, to paint beams and window frames. To paint larger surfaces, such as ceilings or tables, it would be more appropriate to use a 411 spray tip with lacquers or paints / interior materials.

Can you spray stain with a 515 tip?

Fill your Wagner paint sprayer with your deck stain. Note: The Control Pro 130 comes with a 515 spray tip that is great for latex paint. If you’re applying stain, you’ll need a 313 HEA spray tip for stains (sold separately) or 211 HEA spray tip for sealers (sold separately).

Can you spray latex paint with an HVLP sprayer?

HVLP systems are not designed to spray heavier bodied latex paint. If you look at most professional airless paint sprayers designed for latex paint, they are actually pumps, and use no air.

You might be interested:  How Noisy Is An Airless Paint Sprayer?

Are LVLP spray guns any good?

LVLP spray guns are better than HVLP spray guns because they produce few defects. This is because air bubbles can be produced in high volume which can cause a lot of defects. The LVLP uses low pressure and a thin nozzle which allows a low volume of paint to be pushed out of the gun.

Are Graco and Titan spray tips interchangeable?

The tip seats are the same for a Titan gun and a Graco. Some of the Graco tips come with rubber washers instead of plastic, but the metal seats are the same and can be used in either guard. Also the Graco tip guards will fit Titan guns and vice versa.

What PSI should I spray base coat?

When spraying base coat clear coat systems, you want to spray at 26-29 PSI. You measure this PSI by pulling the trigger and letting air flow through the tip of your gun with your dial or digital readout saying 26-29 PSI.

What causes orange peel in paint?

Orange peel is typically the result of improper painting technique, and is caused by the quick evaporation of thinner, incorrect spray gun setup (e.g., low air pressure or incorrect nozzle), spraying the paint at an angle other than perpendicular, or applying excessive paint.

How do I choose a spray gun?

First, you decide on your source of air: compressor or turbine. Second, you choose a spray-gun configuration: siphon-feed, gravity-feed or pressure-feed. Third, you decide on quality – that is, how much you’re willing to pay. And finally you choose a brand.

Leave a Reply

Your email address will not be published. Required fields are marked *