- 1 Do you have to thin paint for a HVLP sprayer?
- 2 What pressure should I set my HVLP spray gun at?
- 3 Is it worth getting a paint sprayer?
- 4 Do you have to dilute paint when using a sprayer?
- 5 Why is my HVLP spray gun spitting?
- 6 Can you spray latex paint with an HVLP sprayer?
- 7 How do I get a smooth finish with spray gun paint?
- 8 Is HVLP better than airless?
- 9 Are electric paint sprayers any good?
- 10 What is the correct pressure for spray painting?
- 11 How big of an air compressor do I need for a HVLP spray gun?
- 12 What is the difference between HVLP and LVLP spray gun?
Do you have to thin paint for a HVLP sprayer?
Latex paint is the most demanding when it comes to straining. They’re extremely viscous, so whenever you spray them with a handheld, HVLP, or small airless sprayer, you need to thin them down.
What pressure should I set my HVLP spray gun at?
We recommend painting between 25-30 psi while the trigger is pulled. You may see some paint tech sheets which refer to a painting air pressure of 8-10. Don’t set the spray gun to those as this measurement is referring to the air cap pressure right where the paint comes out.
Is it worth getting a paint sprayer?
The use of airless paint sprayers is particularly worthwhile in large areas because the advantage of the higher working speed. For a long time, the rule of thumb used to be: use a paint sprayer starting from a 3-room apartment and to paint everything smaller than that roller and brush.
Do you have to dilute paint when using a sprayer?
Is it necessary to Thin Latex Paint for Spraying? Yes, the latex paint does need to be thinned. Even though latex paint is water-based, it is thicker than the oil-based paint varieties. The thick latex paint needs to be thinned to be able to spray a fine mist of paint.
Why is my HVLP spray gun spitting?
“Spitting” happens when your paint gun’s nozzle is not properly screwed into place. If your paint gun is spitting or dripping paint, it is probably because the nozzle is not screwed on tightly. If you’ve checked your nozzle and find that it is screwed on tightly, you may need to purchase a new nozzle altogether.
Can you spray latex paint with an HVLP sprayer?
HVLP systems are not designed to spray heavier bodied latex paint. If you look at most professional airless paint sprayers designed for latex paint, they are actually pumps, and use no air.
How do I get a smooth finish with spray gun paint?
Just wait till the paint is dry and lightly sand it with a fine grit sanding block to smooth it over. Paint over it again and you should be good to go! Here’s a quick video to demonstrate how I spray paint and get a flawless finish every time.
Is HVLP better than airless?
Vertical spraying: An HVLP is better for vertical spraying small projects than an airless, especially if you’re new to spraying. You’re far less likely to get paint runs because you’re spraying at a much lower pressure. An airless cranked up to 2,000 PSI throws a lot of paint onto the surface quickly.
Are electric paint sprayers any good?
While other spray methods vary, laboratory tests have repeatedly shown that airless is by far the most efficient. Without air blowing the finish hither and yon, a very high percentage of coating ends up on the wood. In terms of volume, airless guns move finish much more quickly than any other type of spray gun.
What is the correct pressure for spray painting?
What is the best air pressure for spray painting? Again, it’s essential you check your specific model’s recommendations, but your HVLP spray gun PSI will likely sit between 25-30 PSI for something like using an air compressor for spraying cars, rising to 40 PSI in some cases where higher atomisation is needed.
How big of an air compressor do I need for a HVLP spray gun?
I usually recommend that you use a compressor that has a minimum of 60 gallon tank and produces around 13 CFM.
What is the difference between HVLP and LVLP spray gun?
LVLP is an acronym for Low Volume Low pressure which means that it uses less air volume (5-18 CFM) then HVLP (10-25 CFM) and lower air pressure (10-30 PSI) than a typical conventional Airspray gun (35-60 PSI). LVLP guns have large air passage like the HVLP guns but the air caps have slightly smaller holes.