- 1 How do you read a spray tip?
- 2 What is a 517 spray tip used for?
- 3 What is a 311 spray tip used for?
- 4 What is a 315 spray tip used for?
- 5 What size is a 515 spray tip?
- 6 What size tip should I use to spray clear coat?
- 7 Do I spray walls or ceiling first?
- 8 What is the best spray tip for walls?
- 9 Do I need to thin my paint for airless sprayer?
- 10 Can I spray latex with a 311 tip?
- 11 How do I get a smooth finish with a paint sprayer?
- 12 What size is a 517 spray tip?
- 13 What tip should I use to spray cabinets?
- 14 Are airless paint sprayer tips interchangeable?
How do you read a spray tip?
Understanding the Numbers
- The first digit is half of the fan width, the “5” in “517” equals a 10 inch spray fan width (5 x 2 = 10)
- The last two digits are the size of the tip opening in thousandths of an inch, the “17” in “517” means the tip hole size is. 017 inch.
What is a 517 spray tip used for?
Achieve greater control and less overspray on different surfaces with a wide range of coatings, from stains to exterior paints. 10 inch spray pattern ideal for larger surfaces such as houses/buildings, walls and ceilings.
What is a 311 spray tip used for?
6 inch spray pattern ideal for narrow surfaces such as fences, decks and furniture. The. 011 inch hole size optimal for spraying thinner materials like semi transparent stains, water sealers, stains or polyurethanes. Less overspray shortens cleanup time with less wasted material.
What is a 315 spray tip used for?
The 315 tip is ideal for fence picket priming and painting. The 6” fan pattern minimizes overspray when spraying pickets.
What size is a 515 spray tip?
Thus, a 515 tip denotes an orifice measuring 15 thousandths of an inch in diameter.
What size tip should I use to spray clear coat?
A general rule of thumb is: Heavy-bodied primers and primer surfacers work best when you use a nozzle size of 1.7 to 2.2. Basecoats should be sprayed with a 1.4 to 1.6 nozzle. Clearcoats should be sprayed with a 1.3 to 1.7 nozzle.
Do I spray walls or ceiling first?
Simply spray the ceiling, and let overspray land on the wall and ceiling trim. After the ceiling paint dries, it’s time to paint the walls. Cover the edges with quick-release masking tape and paper — to avoid getting overspray on the ceiling — and start paint spraying the interior walls.
What is the best spray tip for walls?
To paint larger surfaces, such as ceilings or tables, it would be more appropriate to use a 411 spray tip with lacquers or paints / interior materials. To paint rooms or houses, a 515 spray tip would do best.
Do I need to thin my paint for airless sprayer?
They’re extremely viscous, so whenever you spray them with a handheld, HVLP, or small airless sprayer, you need to thin them down. That’s true when you’re using anything other than a big airless unit. If you’re using a handheld or HVLP system to paint, you’re probably going to have to use as much as 20-30% water.
Can I spray latex with a 311 tip?
This airless Sprayer tip was very easy to use and provided great coverage on a new interior door with latex paint using my Graco X5 airless sprayer. The reversible tip made it quick and easy to unclog with just a 180 turn of the top and I was back to spraying my doors. Clean up was relatively easy.
How do I get a smooth finish with a paint sprayer?
Just wait till the paint is dry and lightly sand it with a fine grit sanding block to smooth it over. Paint over it again and you should be good to go! Here’s a quick video to demonstrate how I spray paint and get a flawless finish every time.
What size is a 517 spray tip?
Case in point – a 317 tip and a 517 tip both have the same orifice size – 17-thousandths of an inch. But, the 517 tip sprays a 10-inch-wide fan, while the 317 sprays a 6-inch-wide fan.
What tip should I use to spray cabinets?
Spray Tip Selection When spraying water-based enamel and satin finish paint, it’s best to use a 311 spray tip as it will deliver a 6-inch spray fan that is perfect for cabinets and smaller doors.
Are airless paint sprayer tips interchangeable?
Airless spray tips require their own tip guard/tip holder. These are usually ⅞ fitting, and they’re interchangeable between the different brand guns.