Question: Which Spray Tip Airless Sprayer For Latex Paint?

What is a 515 spray tip used for?

Achieve greater control and less overspray on different surfaces with a wide range of coatings, from stains to exterior paints. 10 inch spray pattern ideal for larger surfaces such as houses/buildings, walls and ceilings.

What is a 311 spray tip used for?

6 inch spray pattern ideal for narrow surfaces such as fences, decks and furniture. The. 011 inch hole size optimal for spraying thinner materials like semi transparent stains, water sealers, stains or polyurethanes. Less overspray shortens cleanup time with less wasted material.

What is a 315 spray tip used for?

The 315 tip is ideal for fence picket priming and painting. The 6” fan pattern minimizes overspray when spraying pickets.

Do you need to thin latex paint for airless sprayer?

Latex paint is the most demanding when it comes to straining. They’re extremely viscous, so whenever you spray them with a handheld, HVLP, or small airless sprayer, you need to thin them down.

You might be interested:  Question: How To Use A Paint Sprayer For Exterior House Painting?

How long does a spray tip last?

Generally a RAC X spray tip will spray around 45 gallons of paint before it needs to be replaced. A RAC IV or RAC V spray tip will last for approximately 40 gallons. All tips will vary depending on pressure that the user is spraying at the the type of paint being sprayed.

Can you spray stain with a 515 tip?

Fill your Wagner paint sprayer with your deck stain. Note: The Control Pro 130 comes with a 515 spray tip that is great for latex paint. If you’re applying stain, you’ll need a 313 HEA spray tip for stains (sold separately) or 211 HEA spray tip for sealers (sold separately).

How do I get a smooth finish with an airless sprayer?

Just wait till the paint is dry and lightly sand it with a fine grit sanding block to smooth it over. Paint over it again and you should be good to go! Here’s a quick video to demonstrate how I spray paint and get a flawless finish every time.

What is a 413 spray tip used for?

Read 0 Reviews Same page link. The Reverse-A-Clean (RAC) 413 RAC IV SwitchTip is designed for narrow surfaces and thinner materials like stains and polyurethanes. The 413 SwitchTip has a 0.013 inch orifice and produces an 8 to 10 inch fan. Reverse the SwitchTip to easily clear clogs.

Can I spray latex with a 311 tip?

This airless Sprayer tip was very easy to use and provided great coverage on a new interior door with latex paint using my Graco X5 airless sprayer. The reversible tip made it quick and easy to unclog with just a 180 turn of the top and I was back to spraying my doors. Clean up was relatively easy.

You might be interested:  Often asked: How To Paint With Cup Style Paint Sprayer Car Rutoleum?

What tip should I use to spray cabinets?

Spray Tip Selection When spraying water-based enamel and satin finish paint, it’s best to use a 311 spray tip as it will deliver a 6-inch spray fan that is perfect for cabinets and smaller doors.

Do you spray ceilings or walls first?

Simply spray the ceiling, and let overspray land on the wall and ceiling trim. After the ceiling paint dries, it’s time to paint the walls. Cover the edges with quick-release masking tape and paper — to avoid getting overspray on the ceiling — and start paint spraying the interior walls.

Can latex paint be sprayed with HVLP gun?

HVLP systems are not designed to spray heavier bodied latex paint. The viscosity (thickness) of latex paint makes it hard for spray guns to fully atomize the paint, meaning that it’s difficult with a lower pressure turbine unit to break the material up into small enough particles to get an ultra smooth surface.

Are airless spray tips Universal?

Airless spray tips require their own tip guard/tip holder. These are usually ⅞ fitting, and they’re interchangeable between the different brand guns.

What size tip is best for spraying clear coat?

A general rule of thumb is: Heavy-bodied primers and primer surfacers work best when you use a nozzle size of 1.7 to 2.2. Basecoats should be sprayed with a 1.4 to 1.6 nozzle. Clearcoats should be sprayed with a 1.3 to 1.7 nozzle.

Leave a Reply

Your email address will not be published. Required fields are marked *